Home

wiki How to Replace Tie Rod Ends

Inner Tie Rod Removal Installation Tool Set Mechanics Kit Dual Tie Rod Tools Durable Steel Construction Comes With Toolbox For Storage

Too low to display


How to Replace Tie Rod Ends Don't leave driving up to luck

This is a quick video showing how to replace an outer tie rod end yourself. Thanks for watching! Please rate, comment, check out my channel & subscribe!

Outer tie rod replacement. Learn how to replace tie rod ends.
This video will show you how to change the outer tie rod of your car or truck. You do not need any special tools to do this job, just a few basic hand tools. The job straight forward and anyone with basic tools can do it!

Find an inexpensive tie rod here:
Socket set I use:
Torque Wrench I used:
Grease Gun:
Chassis Grease for the Tie Rod Ends:

How to tell if your tie rod is bad:
How to replace the inner and outer tie rod:
How to Replace a different outer tie rod:
How to replace a Control Arm:

**If the video was helpful, remember to give it a "thumbs up" and consider subscribing. New videos every Thursday**

-Website:
-Facebook:
-Twitter:
-Instagram:
-Subscribe Here:
-YouTube Channel:

Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.

C6 Corvette How to Replace Tie Rod Ends - Corvetteforum

  • How to Replace Jeep Tie Rod Ends

    Replacing the tie rod ends on your Jeep vehicle is needed when they have worn enough that the toe angle of the...

  • C6 Corvette: How to Replace Tie Rod Ends

    This video is a quick walk through on how to replace tie rod ends on a vehicle. While the vehicle in this video is a 2000 Chevy Blazer, the procedure will be the same or similar on many other vehicles (GMC Jimmy, S10 Pickup, Trailblazer, Envoy, Sierra, Etc). In this video I replaced both the inner tie rod end and the outer tie rod end. I used an air hammer and a pickle fork to separate the tie rods ends, but these tools are not necessary to complete the job. Replacing your own tie rod ends will save you a lot of money and and can be sure that the job is done right. The money you save by doing this yourself will more than pay for any tool or parts that might make the job easier. Good luck and leave questions and comments below.

    Outer tie rod replacement. Learn how to replace tie rod ends.
    This video will show you how to change the outer tie rod of your car or truck. You do not need any special tools to do this job, just a few basic hand tools. The job straight forward and anyone with basic tools can do it!

    Find an inexpensive tie rod here:
    Socket set I use:
    Torque Wrench I used:
    Grease Gun:
    Chassis Grease for the Tie Rod Ends:

    How to tell if your tie rod is bad:
    How to replace the inner and outer tie rod:
    How to Replace a different outer tie rod:
    How to replace a Control Arm:

    **If the video was helpful, remember to give it a "thumbs up" and consider subscribing. New videos every Thursday**

    -Website:
    -Facebook:
    -Twitter:
    -Instagram:
    -Subscribe Here:
    -YouTube Channel:

    Disclaimer:
    Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.